"); //-->
广州英码信息科技 武汉办事处 唐成卫 13886107045 1. Key Features
SOM35X module(*) |
Processor |
TI OMAP3530 |
600MHz ARM Cortex™-A8 Core NEON™ SIMD Coprocessor 430MHz TMS320C64x+ DSP POWERVR SGX™ Graphics Accelerator |
RAM |
256MByte mDDR |
||
Flash |
512MByte Nand Flash |
||
LED |
1x SOM35X power supply indicator |
||
1x Heartbeat indicator |
|||
Ethernet |
1x 10M/100M high performance Ethernet with HP Auto-MDIX support (RJ45) |
||
LCD |
1x 4.3 inch LCD interface |
Resolution: 272x480 |
|
4-wire touch screen support |
|||
Software controlled backlight |
|||
Audio |
1x 1W software controlled mono speaker interface |
||
LED power supply |
1x Software controlled 12V LED interface (2x connectors) |
||
1x Software controlled 12V LED interface (1x connector) |
|||
UART |
1x TTL UART interface (3-wire: TX, RX, GND) |
||
1x RS232/RS485 interface (Hardware jumper selection) |
|||
1x RS232 debug console interface (3-wire: TX, RX, GND) |
|||
Wiegand |
1x 5V Wiegand input interface |
||
1x 5V Wiegand output interface |
|||
USB Host |
4x HSUSB Host 2.0 |
3x Camera interface |
|
1x HSUSB interface |
|||
I2C |
1x 5V I2C interface |
||
SD card slot |
MMC/SD/SDHC card slot, support up to 32GByte |
||
RTC battery slot |
1x CR1220 RTC battery slot |
||
Digital I/O |
4x 5V Digital output |
||
4x 5V Digital input |
|||
1x Intrusion detection switch input |
|||
Key |
1x Reset |
||
1x Restore to manufacture |
|||
LED indicators |
2x Power indicators |
||
2x Wiegand input data indicators |
|||
2x Wiegand output data indicators |
|||
2x TTL data indicators |
|||
2x RS232/RS485 data indicators |
|||
Power supply |
1x 12V DC Power supply |
(*)SOM35X module is not included in FV3530 mainboard.
Parameter |
Min |
Typical |
Max |
Unit |
Remark |
DC Main Power Supply Voltage |
11.5 |
12 |
12.4 |
V |
(*1) |
DC Main Power Supply Current(*2) |
0.2 |
2 |
3 |
A |
|
DC Main Power Supply Current(*3) |
0.2 |
0.5 |
1 |
A |
|
RTC Backup Battery Voltage |
1.8 |
3.2 |
3.3 |
V |
|
Storage Temperature |
-20 |
/ |
60 |
°C |
|
Operating Temperature |
-10 |
25 |
50 |
°C |
|
(*1) Onboard over-voltage protection scheme protects fill light, Wiegand power output against high-voltage faults. The lockout threshold varies from 12.4V to 12.8V as the temperature varies.
(*2) In situation that with fill light and Wiegand card reader.
(*3) In situation that without fill light and Wiegand card reader.
Reference |
Interface |
Remark |
CON1 |
12V DC power input |
Opposing current protection Over-voltage protection(*1) Over-current protection (*2) |
CON2 |
Ethernet |
|
CON3 |
Upper: RS232/RS485 interface |
|
Lower: RS232 debug console interface |
|
|
CON4 |
SD Card slot |
|
CON5 |
LCD interface |
Compatible with AT043TN24 |
CON6 |
External camera module interface |
|
CON7 |
Upper: Wiegand input interface |
5V I/O |
Lower: Wiegand output interface |
5V I/O |
|
J1, J2, J3, J4 |
SOM35X module interfaces |
|
J5 |
TTL interface |
5V I/O |
J6 |
Internal RS232/RS485 interface |
Onboard 120Ω termination resistor (*3) |
J7 |
Digital output interface |
5V I/O |
J8 |
Digital input interface |
5V I/O |
J9 |
Speaker interface |
8Ω 1W |
J10 |
Fill light interface |
12V DC PWM dimming |
J11 |
Fill light interface |
12V DC PWM dimming |
J12 |
AD. light interface |
12V DC PWM dimming |
J13, J14 |
Onboard camera interface |
|
J15, J16 |
Onboard camera interface |
|
J17 |
High speed USB interface |
|
J18 |
I2C interface |
5V I/O |
J19 |
Internal Wiegand input interface |
5V I/O |
J20 |
Intrusion detection |
1.8V I/O |
(*1) Onboard over-voltage protection scheme protects fill light, Wiegand power output against high-voltage faults. The lockout threshold varies from 12.4V to 12.8V as the temperature varies.
However, the main system still maintains normal operation in over-voltage condition.
Onboard surge protection device protects the system against surge damage from power supply.
DO NOT USE A POWER SUPPLY HIGHER THAN 16V OTHERWISE WILL CAUSE DAMAGED TO BOTH THE SYSTEM AND THE POWER SUPPLY.
(*2) A 3Amp fuse used as over-current protection.
(*3) The characteristic impedance of the data cable should be 120Ω according to the TIA/EIA-485 standard.
Reference |
Switch |
Remark |
SW1 |
Boot mode switch |
Flash then SD card: 111100 SD card only: 000110 Flash only: 101010 |
J21, J24, J25, J26 |
RS232/RS485 interface mode switch |
|
SW4 |
Reset |
|
SW5 |
Restore to manufacture |
|
Reference |
LED |
Remark |
D6 |
3.3V power supply indicator |
|
D7 |
5V power supply indicator |
|
D11 |
TTL TX data indicator |
|
D12 |
TTL RX data indicator |
|
D13 |
RS232/RS485 TX data indicator |
|
D14 |
RS232/RS485 RX data indicator |
|
D22 |
Wiegand output D0 data indicator |
|
D23 |
Wiegand output D1 data indicator |
|
D24 |
Wiegand input D0 data indicator |
|
D25 |
Wiegand input D1 data indicator |
|
SOM35X.D2 |
SOM35X heartbeat |
|
SOM35X.D3 |
SOM35X power supply |
|
External camera module |
RJ45 |
Wiegand input |
RS232/RS485 |
DC IN |
Wiegand output |
Debug RS232 |
|||
PCB |
The main power input for the system is provided using an external 12V DC supply. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
+12V DC power input |
|
2 |
Power ground |
|
3 |
Shield ground |
An onboard 10nF/2KV capacitor bridged between Shield ground and power ground. |
The RS232/RS485 interface is used to provide an interface to RS232/RS485 card reader. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
TX/A |
|
2 |
RX/B |
|
3 |
GND |
|
The working mode is selected by J21, J24, J25, J26.
Mode |
Switch |
RS232 |
J21: Short 1,2 J24: Short 1,2 J25: Short 1,2 J26: Open |
RS485 |
J21: Short 2,3 J24: Short 2,3 J25: Short 2,3 J26: Short |
The interface is used to provide a debug console to system. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
TX |
|
2 |
RX |
|
3 |
GND |
|
The SD card slot is used to provide an interface to a MMC/SD/SDHC card. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
DAT2 |
|
2 |
DAT3 |
|
3 |
CMD |
|
4 |
C/D |
1.8V I/O |
5 |
VSS |
|
6 |
VDD |
3V |
7 |
CLK |
|
8 |
VSS |
|
9 |
DAT0 |
|
10 |
DAT1 |
|
11 |
W/P |
1.8V I/O |
The LCD interface connector is a 40 pin FFC SMD connector for LCD. Pin definition is compatible with Chimei Innolux AT043TN24. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
LED- |
|
2 |
LED+ |
|
3 |
GND |
|
4 |
VDD |
3.3V |
5 |
R0 |
|
6 |
R1 |
|
7 |
R2 |
|
8 |
R3 |
|
9 |
R4 |
|
10 |
R5 |
|
11 |
R6 |
|
12 |
R7 |
|
13 |
G0 |
|
14 |
G1 |
|
15 |
G2 |
|
16 |
G3 |
|
17 |
G4 |
|
18 |
G5 |
|
19 |
G6 |
|
20 |
G7 |
|
21 |
B0 |
|
22 |
B1 |
|
23 |
B2 |
|
24 |
B3 |
|
25 |
B4 |
|
26 |
B5 |
|
27 |
B6 |
|
28 |
B7 |
|
29 |
GND |
|
30 |
PCLK |
|
31 |
DISP |
|
32 |
HSYNC |
|
33 |
VSYNC |
|
34 |
DE |
|
35 |
NC |
|
36 |
GND |
|
37 |
X+ |
|
38 |
Y+ |
|
39 |
X- |
|
40 |
Y- |
|
The interface is used to provide an interface to an external camera module, include interfaces for USB camera and fill light. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
USB +5V DC power output |
|
2 |
USB DP |
|
3 |
USB DM |
|
4 |
GND |
|
5 |
USB shield ground |
|
6 |
USB shield ground |
|
7 |
Fill light ground |
For fill light only |
8 |
+12V Fill light power output |
|
The interface is used to provide an interface to a standard Wiegand card reader. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
+12V DC power output |
|
2 |
Wiegand input D0 |
5V I/O |
3 |
Wiegand input D1 |
5V I/O |
4 |
GND |
|
The interface is used to provide an interface to output Wiegand data to an upper host. The pin-out for the connector is shown in the table below.
Pin number |
Pin definition |
Remark |
1 |
+12V DC power output |
|
2 |
Wiegand output D0 |
5V I/O |
3 |
*博客内容为网友个人发布,仅代表博主个人观点,如有侵权请联系工作人员删除。 ![]() 最近文章
|